Sub-Zero fridge not cooling: causes and fixes


When a Sub-Zero fridge is not cooling, the cause we find most often is a condenser blocked with dust; after that come a leaking or iced-up evaporator, a failed fan motor, and a control board or inverter that has overheated or failed after a power cut. This guide from LE Company, Sub-Zero repair engineers in London, is based on our own job records: more than 900 Sub-Zero requests since 2022, of which more than 100 were about a Sub-Zero that was warm or not cooling. For other brands, see fridge freezer not cooling. Every repair we do starts with checking and cleaning the fridge, because most faults begin with dust, scale, grease or a blockage. For repairs, see our Sub-Zero repair in London page.

Why is my Sub-Zero fridge not cooling?

These are the causes behind the Sub-Zero cooling jobs in our records, most common first:
  • A condenser blocked with dust. The condenser cannot get rid of heat, the compressor runs longer and hotter, and in the end the control board, the inverter or the compressor overheats. On one Sub-Zero the compressor would not start and had reached 90°C.
  • The evaporator and the refrigerant. Refrigerant gas appears on more than 70 of our Sub-Zero jobs and evaporators on more than 50. A cracked or damaged evaporator lets the gas leak out slowly, so the fridge gets warmer week by week.
  • Fan motors. Fan motors and blades appear on more than 30 Sub-Zero jobs. When the condenser fan stops, the heat stays in the machine compartment; when the evaporator fan stops, the cold stays at the coil and never reaches the shelves.
  • The control board and the inverter. Sub-Zero compressors are driven by an inverter and controlled by the main board. Both fail after overheating, and boards also fail after a power cut.
  • The compressor. Compressors appear on around 60 of our Sub-Zero jobs. A compressor that has lost power runs all the time but cannot pull the temperature down.
  • Defrost faults, seals and doors. A defrost fault lets ice build up on the evaporator until air stops flowing. A worn seal or a door that has dropped lets warm air in all day.
If the display shows a code or a flashing Service light, read our guide to Sub-Zero error codes first: a long-run code such as 40 1 40 or EC50 is often the first sign of a cooling problem.

What to check first: Sub-Zero’s own steps

Sub-Zero’s help page on warm refrigerator troubleshooting (subzero-wolf.com) lists these owner checks. They are safe to do yourself:
  • The setting. Sub-Zero recommends 38°F (about 3°C) for the refrigerator. After changing it, allow 24 hours.
  • The door. Make sure it closes fully, nothing blocks it, and the door seal is not damaged.
  • Warm shopping. A load of warm food raises the temperature for several hours; that is normal.
  • The condenser. Clean it if it has not been cleaned in the last 6 months. Sub-Zero’s condenser cleaning page for Classic (Built-In) and PRO 48 models says to switch the unit off at the control panel, lift the bottom grille and vacuum the condenser with a soft brush attachment, every six to twelve months. Temperatures can take up to 24 hours to recover.
  • Sabbath mode. If the control panel does not respond or shows no temperatures, check that Sabbath mode is not on.
  • Note which section is warm. Sub-Zero asks for this, and it helps the engineer too.
Sub-Zero adds one important limit: if the fridge is above 48°F (about 9°C) with the setting at 38°F, it is unlikely to recover from a condenser cleaning, and an engineer is needed. Do not open panels beyond the grille, and never touch the sealed refrigerant system or the mains wiring: that work needs an F-Gas registered engineer. Keeping the condenser clean is part of regular Sub-Zero maintenance.
Sub-Zero machine compartment with the grille removed

Sub-Zero fridge not cooling but freezer works

First rule out the simple case. Sub-Zero says that if the refrigerator is not cooling, its lights are off and the freezer is working, the refrigerator may have been switched off on its own: a control showing double dashes (--) means that section is disabled. Switching it back on is described on Sub-Zero’s help pages for each series.
If the fridge section is switched on and still warm while the freezer is fine, the cause we find most is the evaporator. On one Sub-Zero the fridge section had overheated and was low on gas; the engineer advised a new evaporator and a regas. The original fan motor was out of stock, so we offered a digital fan motor with a relay, which in our experience is quiet and reliable. We replace evaporators on Sub-Zero fridges up to 20 years old; after the new evaporator is fitted, the sealed system is cleaned and regassed.
Many Sub-Zero models have a separate compressor for each section, which is why one part can stay cold while the other warms up. On a fridge with a wine section above, the wine section kept working while the fridge below was warm; the owner had already cleaned the filter, and the fridge compressor had to be replaced. If it is the freezer that is warm, see our Sub-Zero freezer repair page; for wine storage, see Sub-Zero wine fridge repair.
Sub-Zero fridge display showing 20°C in the fridge section
Sub-Zero evaporator covered in ice behind the rear panel

Sub-Zero fridge not cooling after power outage

Start with Sub-Zero’s reset: switch the unit off at the control panel, switch the breaker for the fridge off for 30 seconds, switch it back on and give it 24 hours. Check that the breaker or fuse has not tripped. On Classic models a power drop can also be logged as a brownout code; our Sub-Zero error codes guide explains it.
If the fridge does not come back, the control board is the usual cause in our records. On a Sub-Zero fridge freezer in North London, a power outage left the fridge not working at all; the main board had failed and was replaced. Another Sub-Zero came to us with no display and no cooling, and again it was the board. When a board is suspected, our engineer fits a test board on site to prove it before a new one is ordered. A power cut can also damage the inverter that drives the compressor, which is tested at the same visit.

Sub-Zero fridge not cooling enough

A Sub-Zero that is cool but not cold enough is usually struggling rather than broken. The causes we find:
  • No air for the condenser. On a Sub-Zero with a wine section in a very warm flat, the cooling could not cope; when our engineer removed the outer design grille, it started to work again. Sub-Zero itself warns that a grille or kickplate covered by cabinetry can starve the unit of air. Another fridge, fitted into a tight cupboard and overloaded, needed a full fan clean before it cooled again: see our Sub-Zero cooling job.
  • A weak compressor. On one Sub-Zero the compressor had lost power and could not bring the cabinet down to temperature; the recommended fix was a new compressor with its inverter.
  • A fan that is failing. After a temporary fan repair, one Sub-Zero stopped cooling; it needed the original condenser fan motor and blades. On an older unit, a new compressor alone did not reach temperature, and the fan motor had to be replaced as well.
  • Ice on the evaporator. On one Sub-Zero a defrost fault had iced up the evaporator and the compressor never stopped. We defrosted it by hand and recommended new defrost parts and a new control board.
  • A door that does not close. On a Sub-Zero freezer the door had dropped and left a gap, so warm air came in and the coil iced over.

Sub-Zero fridge stopped cooling completely

If the light is on but nothing is cold, the compressor is not running. In our records that comes down to the control board, the inverter or the compressor itself, and very often it follows years of a dusty condenser. Cleaning alone is not always enough: one owner had vacuumed the condenser, but the fridge still did not cool, and the engineer found a failed board and a worn door seal. Sub-Zero also warns about showroom mode on a newly installed unit: the display shows normal temperatures, but nothing cools.
If the fridge also leaks water or trips the electrics, tell us when you book: a Sub-Zero drawer unit we repaired was tripping the breaker during defrost because of failed defrost heaters.

When to call a Sub-Zero engineer

Call an engineer if the fridge is above about 9°C after the checks above, if one section is warm and the other is fine, if it did not recover 24 hours after a reset, or if a code keeps coming back. Move food that must stay cold to another fridge, and keep the door shut. Whether a repair on an older unit is worth it depends on the fault; our Sub-Zero repair cost guide explains how to decide.

Book a Sub-Zero repair in London

LE Company’s call-out is from £175 + VAT and includes the first 30 minutes on site, when the engineer finds the cause of the fault. The cost of the repair is agreed with you before any work starts. 12-month guarantee on parts — we fit only original manufacturer parts. Call +44 203 603 7172.
The visit with the assessment is paid first. Our engineers are Gas Safe and F-Gas registered, so refrigerant work is done by us on site. We work Monday to Saturday, 8am to 8pm; Sunday visits are for service-contract customers only. See our Sub-Zero repair page, our full appliance repair in London, or read our frequently asked questions.

Book an engineer

Leave your details and what is wrong. The bookings team will email you the call-out cost and the times an engineer can come. Call-out from £175 + VAT, including the first 30 minutes on site.