Smeg oven error codes: what they mean and what to do
The Smeg oven error code with a published meaning is ERR4 (Error 4): the door lock did not engage at the start of pyrolytic cleaning, and switching the oven off and on and starting a new cycle usually clears it; codes F1, F3, F4, F5, F8, F, FF, E0, E2 and E3 on a pyrolytic oven need an engineer, and for any other Error XX Smeg asks you to note the code and call for service. This guide from LE Company, Smeg repair engineers in London, lists what Smeg’s own manuals and Smeg UK’s help pages say about each code, what you can safely check yourself, and when to call us. For repairs, see our Smeg oven repair page.

Smeg oven error codes list
Every meaning below comes from a Smeg document: the “What to do if...” section of Smeg user manuals downloaded from Smeg UK (smeguk.com/info/download-manuals), and the Smeg UK help pages (help.smeguk.com). Smeg publishes a meaning for only a few codes. For the rest it tells owners which codes need an engineer, so we list them that way and do not guess.
Code | What Smeg says | Smeg document and models |
ERR4 / Error 4 | The door lock has not attached to the door properly, possibly because the door was opened while the lock was engaging. Switch off and on, wait a few minutes, start a new cleaning cycle | User manuals of pyrolytic ovens (SFP130, SFP6390XE, SFP6604PNXE, SFP6303WTPX, SFP9305WSPX) and pyrolytic cookers (Opera A1PYID-9, Portofino CPF9IPX); ERR 4 on older SC112 |
F1, F3, F4, F5, F8, F, FF | The oven needs an engineer’s visit. No meaning is published for owners | Smeg UK help page for pyrolytic ovens |
E0, E2, E3 | The oven needs an engineer’s visit | Smeg UK help page for pyrolytic ovens |
Any other Error XX / ERRx | Note down the code, the function and the set temperature, and contact technical support | Same user manuals as ERR4 |
Err1 | The temperature sensor connector is not properly connected to the circuit board, or has short-circuited. Clears when the power is switched off; if it persists, call for service | Manual of the Smeg ALFA201XE professional convection oven, section 4.13.1 |
Two probe error messages | The temperature probe is not reading the food correctly; after you acknowledge them, the oven carries on with timed cooking | Manuals of ovens with a probe (SFP6303WTPX, SOP6604TPNR, SO6606WAPNR) |
Er03, Er20, Er22, Er31, Er47, E/2, E/5, E/6, E/7, E/9, U400 | Induction hob of a cooker: an engineer is required | Smeg UK help page for cooker induction hobs |
Smeg oven error 4
According to Smeg’s user manuals, ERR4 (shown as Error 4 on some models) means the door lock has not properly attached to the door, possibly because the door was opened while the lock was engaging at the start of pyrolytic cleaning. Smeg’s advice is to switch the oven off and on again, wait a few minutes, and then select a new cleaning cycle. The same text appears in the manuals of pyrolytic ovens such as the SFP130, SFP6390XE, SFP6604PNXE, SFP6303WTPX and SFP9305WSPX, of the Opera A1PYID-9 and Portofino CPF9IPX pyrolytic cookers, and as ERR 4 on older built-in models such as the SC112, where Smeg notes it appears on pyrolytic models only.
If the door was closed the whole time and Error 4 comes back on every cleaning cycle, the lock itself is not engaging, and that is a job for an engineer. Stop running the cleaning cycle until it has been checked.
Smeg oven error code F3
Smeg UK’s help page “I have an error code on my pyrolytic oven – what does it mean?” lists F3 together with F1, F4, F5, F8, F, FF, E0, E2 and E3, and says that any of these codes will require an engineer’s visit. Smeg does not publish what each of these codes means for owners, and we will not guess: the meaning depends on the model and its control board, and the engineer reads it on site. Note down the code, take a photo of the display, and do not keep restarting the oven to make the code go away.
Smeg oven error code 5, 6, 7, 8 or 9
We could not find an official Smeg meaning for Error 5, 6, 7, 8 or 9 on an oven, so they are not in the table. Smeg’s manuals give one instruction for every error message other than Error 4: note down the error message, the function you were using and the set temperature, and contact technical support. Send us the same three details with your enquiry, plus the model number from the plate inside the door frame, and our engineer comes prepared.
Smeg cooker error codes
On a Smeg range cooker, the oven codes are the same as on a built-in oven: the Opera A1PYID-9 and Portofino CPF9IPX manuals describe ERR4 exactly as above. The induction hob of a cooker has its own codes. Smeg UK’s help page for cooker induction hobs lists Er03, Er20, Er22, Er31, Er47, E/2, E/5, E/6, E/7, E/9 and U400 as codes that need an engineer. The same page says that a hob display that is simply flashing means the hob is in showroom mode or the child safety lock is on, which you can reset by following the user manual.
Smeg oven door locked after cleaning
This is not a fault. Smeg’s manuals explain that the door locks about two minutes after a pyrolytic cycle starts, and that no function can be selected while the lock is active, because the oven is still too hot to cook. Wait for the oven to cool and the lock to release. Smeg’s own figures show how hard the cycle is: pyrolysis runs for 180 to 210 minutes, and the front glass can reach about 145°C. Do not force the door. Smeg also warns that pyrolysis cannot start with the temperature probe plugged in: the oven gives an error signal each time you press START.
Smeg oven showroom mode: display on, but no heat
If the display, light and fan work but the oven does not heat up, check the settings menu first. Under “The appliance does not heat up”, Smeg’s manuals say to check whether demo mode or Showroom mode is on. Showroom mode switches off all the heating elements and keeps the control panel working. Set it to Off. If it is already off, the heat is missing for a real reason, and the usual causes are the ones we describe in why your Smeg oven stops working: a heating element, the mode switch or burnt connections.
Smeg oven tripping the electrics: no code at all
Many Smeg oven faults never show a code. Smeg UK’s help page on appliances that trip the electrics lists an overloaded circuit, a terminal block at the back of the oven that is not tight enough, and faulty parts: a heating element, the selector switch, the fan, the thermostat or the oven lamp. Smeg suggests trying different functions to see which one trips, and recording a video of the fault. Leave the terminal block and the wiring to an engineer: that is mains electrics.
What our engineers find on Smeg ovens
From our job records, LE Company has had more than ten requests since 2022 that name a Smeg oven or cooker, and not one of them was about an error code. Owners describe what the oven does: it does not heat although the light and fan come on; the electric oven will not turn on while the gas hob still works; both ovens of a cooker about 15 years old stopped together; the light will not switch off; the clock has stopped. A code tells you that the control has noticed something. What the oven does tells our engineer where to start.
What we found behind those symptoms (a failed light section on the main board, heating elements, worn door hinges and rollers, burnt connections, a thermocouple on a gas cooker) is written up in our Smeg oven fault cases, so we do not repeat it here. One thing links most of them: heat and grease. Every repair we do starts with checking and cleaning the appliance, because most faults begin with dust, scale, grease or a blockage, and on an oven that means grease on terminals, switches and the fan.
How to reset a Smeg oven error code
In the Smeg documents we checked, a reset is given for two codes only. For ERR4, switch the oven off and on again and wait a few minutes before starting a new cleaning cycle. For Err1 on the ALFA201XE, the error clears when the oven’s power supply is switched off. For every other code Smeg does not give a reset: note the code, the function and the temperature, and book an engineer. A code that comes back after a restart is still there, however many times it is cleared.
When to call a Smeg oven engineer
Call an engineer if you see any F or E code from the list above, if Error 4 returns with the door closed, if the oven does not heat with showroom mode off, or if it trips the electrics. Do not open the back panel and do not touch gas parts yourself. Our engineers are Gas Safe and F-Gas registered and repair Smeg ovens, cookers and built-in appliances across London; see our Smeg repair service, our oven repairs in London, or all our appliance repair in London.
Book a Smeg oven repair in London
LE Company’s call-out is from £175 + VAT and includes the first 30 minutes on site, when the engineer finds the cause of the fault. The cost of the repair is agreed with you before any work starts. 12-month guarantee on parts — we fit only original manufacturer parts. The visit with the assessment is paid first. We work Monday to Saturday, 8am to 8pm; Sunday visits are for service-contract customers only. See our Smeg oven repair page, read our frequently asked questions, or call +44 203 603 7172.