Sage coffee machine error codes: what they mean and what to do


A Sage coffee machine shows two kinds of warning: alerts you can clear yourself, such as FILL TANK, CLEAN ME, a descale reminder or a flashing light for an open steam lever or an unlocked hopper, and fault messages, such as ERR on the Oracle, Operation Error on the Oracle Touch, E1, E2 or E3 on the Dual Boiler and ERROR MODE on the Barista Pro, which Sage says need its customer service or a service engineer. Numbered codes such as ER05 or Error 12 are not explained in Sage’s UK instruction books, so for those Sage’s advice is to restart the machine, then do a factory reset, then contact support. This guide from LE Company, which has handled more than 3,000 Sage requests in London since 2022, lists what each message means according to Sage’s own documents and what our engineers find behind them. For repairs, see our Sage coffee machine repair page.

Sage coffee machine error codes list

The meanings below are taken only from Sage’s own UK instruction books, user guides and quick guides, published on sageappliances.com. Each Sage model has its own display and its own messages, so check which machine you have: the model number (for example SES880 or BES880) is on the label under the machine.
Message or code
What Sage says it means
Model and Sage document
ERR on the LCD
A major fault has occurred and the machine cannot operate (the Instruction Book also lists a portafilter not locked in, a wet or dirty basket rim, or a clock / Auto Start setting). Contact Sage Customer Service.
The Oracle (BES980 / SES980), UK Instruction Book and UK User Guide
Operation Error on the touch screen
Clock or Auto Start time not set correctly, or a major fault has occurred and the machine cannot operate. Contact Sage Customer Service.
The Oracle Touch (BES990 / SES990), UK Instruction Book
E1, E2 or E3 on the LCD
An error that cannot be reset by the user has occurred. Contact Sage Customer Service.
The Dual Boiler (BES920 / SES920), UK Instruction Book
ERROR MODE on the LCD
Contact Sage Customer Service.
The Barista Pro (BES878 / SES878), UK Quick Guide
OVERHEAT PLEASE WAIT
The grinder has been used too much and needs time to cool.
The Oracle, UK User Guide
FILL TANK
The machine has detected a low water level. If it shows with a full tank, push the tank in fully and close the latch.
The Oracle, the Dual Boiler
CLEAN ME!
200 extractions since the last cleaning cycle: run the cleaning cycle.
The Oracle, the Dual Boiler
FLUSH / DESCALE
A cleaning cycle (FLUSH) or a descale (DESCALE) is due.
The Barista Pro, UK Quick Guide
Sage does not publish a single list of numbered error codes for its espresso machines. Its support article on error codes, written for the Barista Pro, Barista Touch, Dual Boiler, Oracle and Oracle Touch, says that codes and messages vary by model and points owners to the instruction book for their machine.

Sage coffee machine error 05 (ER05 start up error)

ER05, also written as error 05 or error 5, is the code Sage owners ask us about most: around 20 requests in our job records since 2022 mention it, most of them from Barista Touch owners who see it when they switch the machine on. We could not find ER05 in Sage’s UK instruction book for the Barista Touch (BES880 / SES880), nor in any other Sage UK instruction book or support page, so we do not give it a meaning here.
What Sage does say, in its support article for espresso machines that show an error code or message, is:
  • Restart the machine: switch it off, unplug it, wait 60 seconds, plug it back in and switch it on.
  • If the code returns and your model has a Factory Reset option, run it from the settings menu. Sage warns that a factory reset can erase saved drinks and custom settings.
  • If the code is still there, contact Sage Customer Support with the model number, serial number, the exact message and what you have tried.
Many owners tell us they have read online that ER05 means a faulty milk temperature sensor. That may or may not be the cause on your machine. One owner bought a replacement part online, fitted it, and the code stayed. Our engineers do not guess from a code: they test the part, its wiring and the board that reads it before anything is replaced.

Sage coffee machine error 12

Error 12 (ER12) is not listed in Sage’s UK instruction books either. In our job records it was reported on Oracle Touch machines. In one case an Oracle Touch made a loud rattling noise, showed ER12, and when it was switched off and on again it blew the kitchen fuse and would not switch on at all. The machine came to our workshop for a full service with a service kit. When a Sage trips the electrics, do not keep switching it back on: unplug it and call an engineer.

Sage Oracle error codes: ERR and Operation Error

On the Oracle (BES980 / SES980), Sage’s UK Instruction Book lists ERR on the LCD for a portafilter that is not locked in properly, a wet or dirty filter basket rim, an Auto Start clock that is not set, and a major fault that stops the machine working. The newer UK User Guide simply says ERR means a major fault and the machine cannot operate. On the Oracle Touch (BES990 / SES990), the UK Instruction Book lists Operation Error on the touch screen for a clock or Auto Start time that is not set correctly, or a major fault that stops the machine.
If you see ERR, first lock the portafilter in fully, dry the basket rim and check the clock. If ERR stays, Sage’s advice is to contact customer service. In our jobs, an Oracle that stopped working with ERR needed a new circuit board after a workshop investigation. An Oracle Touch that showed error 15 and would not go past it needed a new steam wand, fitted during a full service. And on an Oracle that showed error 05, the milk jug temperature probe was replaced as part of its service.

Sage coffee machine error lights

Machines without a screen, such as the Barista Express and the Bambino Plus, use flashing lights instead of messages. Most of them are reminders, not faults. Here is what Sage’s own guides say:
Light
What Sage says it means
Model and Sage document
POWER light flashing
The machine is heating up. It stops flashing when it is ready.
Barista Express (BES875 / SES875), UK User Guide
FILTER SIZE lights flashing
The bean hopper is not locked in place. Remove it, clear any debris and lock it back.
Barista Express, UK User Guide
STEAM / HOT WATER light flashing at switch-on
The dial is not in the STANDBY position. Turn it to STANDBY and the machine will heat.
Barista Express, UK User Guide
Filter lights flashing between single and double
The hopper is not attached correctly.
Barista Express Impress (BES876 / SES876), UK User Guide
Two red dose lights flashing and 3 beeps
Low coffee beans: add beans to the hopper.
Barista Express Impress, UK User Guide
Maintenance light flashing / on solid
Flashing: a cleaning cycle is due. Solid: a descale is due.
Barista Express Impress, UK User Guide
STEAM or HOT WATER LED flashing at start-up
The steam lever or the hot water dial is open. Close it and the machine will start.
The Dual Boiler, UK Instruction Book
MANUAL flashing on the steam display
The steam lever is in the MANUAL position. Lower it to the centre OFF position.
The Oracle, UK User Guide
Milk temperature and froth lights flashing together
Steam function error: the steam wand is blocked or the tank may be empty. Hold the STEAM button for 3 seconds to purge, and fill the tank.
Bambino Plus (BES500 / SES500), Quick Guide
1 CUP and 2 CUP flashing alternately
A cleaning cycle is due.
Bambino Plus, Quick Guide
Sage’s guides also explain a machine that is on but suddenly stops working: the safety thermal cut-out may have switched it off because the pump or grinder overheated. Switch it off, unplug it and let it cool for 30 to 60 minutes. If it happens again, it needs an engineer.
Sage coffee machine warning: what you can fix yourself and when to call an engineer

Why is my Sage coffee machine flashing?

If all the lights flash, or two lights flash together, check the simple things first: water in the tank, the tank pushed fully in, the hopper locked, the steam lever or hot water dial closed, and the steam wand clear. On a Bambino Plus, Sage says the milk temperature and froth lights flashing together mean a steam function error, and the fix is a 3-second steam purge and a full tank. Several Bambino Plus owners have contacted us with all the lights flashing, and a blocked steam wand is the first thing to rule out. If the lights keep flashing after that, the machine needs to be checked.

Sage coffee machine fault finding: what to do first

  • Write down the exact message or which lights flash, and the model number. Take a photo or a short video.
  • Restart the machine: unplug it for 60 seconds. On models with a Factory Reset option, try it if the code returns.
  • Fill the tank, lock the hopper and the portafilter, close the steam lever and the hot water dial.
  • If the machine is due a descale, run the descale cycle from the machine itself. Sage warns not to descale the Oracle Touch any other way.
  • Do not open the machine. A Sage has mains voltage, boilers under pressure and very hot parts inside.
If the problem is not a code but a symptom, such as no pressure, no steam, a grinder that will not grind or a leak, see our guide to Sage coffee machine common faults.

What our engineers find behind a Sage error message

More than 50 of our Sage requests mention an error code, an error message or flashing lights. A code tells the engineer which system has a problem, not which part has failed. Every repair we do starts with checking and cleaning the machine, because most faults begin with dust, scale, grease or a blockage: a sensor coated in scale or a blocked steam wand can produce the same message as a failed part.
Our job records show the pattern. A service kit and a full service appear on more than 200 Sage jobs, far more than any single part. Behind the messages that did need a part we most often found:
  • Power boards and control boards, on more than 25 jobs: burnt components on the board that drives the heaters and valves, or a board that kept the boiler powered after the machine was switched off. Some boards can be repaired rather than replaced.
  • Probes, sensors and electrodes, on about 20 jobs: the steam and milk temperature probes on the Oracle and Oracle Touch, water level electrodes and temperature sensors.
  • Thermal fuses, valves, pumps and boilers, where scale or heat has done its damage.
Regular care prevents many of these messages. Descale when the machine asks, change the water filter, purge the steam wand after every use, and book a coffee machine service every year or two. Our home coffee machine care guide explains the routine.

Book a Sage repair in London

LE Company’s call-out is from £175 + VAT and includes the first 30 minutes on site, when the engineer finds the cause of the fault. The cost of the repair is agreed with you before any work starts. 12-month guarantee on parts — we fit only original manufacturer parts. The visit with the assessment is paid first. We work Monday to Saturday, 8am to 8pm. See our Sage coffee machine repair and coffee machine repair in London pages, our appliance repair in London services, or call +44 203 603 7172.

Book an engineer

Leave your details and what is wrong. The bookings team will email you the call-out cost and the times an engineer can come. Call-out from £175 + VAT, including the first 30 minutes on site.