Carpigiani 191 error codes and display messages


On a Carpigiani 191 or 193 soft serve machine, WAS on the display means a wash is due within the next few days, and W followed by a number counts the days until the next wash. Alarms start with A: A01 to A05 stop the machine (thermal protections, safety thermostats, tank sensor), A09 means the front lid is open, and A11 means the high pressure switch has tripped. LE Company repairs Carpigiani and other soft serve and gelato machines in London; since 2022 we have handled about 200 ice cream machine requests. For our full service, see ice cream machine repair in London.
Carpigiani soft serve machine display showing WAS, wash due

What does WAS mean on a Carpigiani?

WAS is a reminder, not a fault: the machine is telling you the wash cycle is due in the last few days before cleaning. Because the display has only three seven-segment digits, WAS reads like “uA5”, and the countdown W with a number reads like “u” followed by digits. Clean the machine as the manual describes and the countdown starts again.
Carpigiani soft serve display showing the W countdown to the next wash

Carpigiani 191 alarm codes

The meanings below are from the published troubleshooting guide for the Carpigiani 191 and 193. Check your own model’s manual: other Carpigiani machines use different codes.
Code
Meaning
What happens
A01
Thermal protection tripped
Machine stops
A02
Compressor thermal relay or protection tripped
Machine stops
A03 / A04
Tank / cylinder safety thermostat tripped
Machine stops
A05
Tank sensor faulty
Machine stops
A06
Cylinder sensor faulty
Stops during pasteurisation or storage
A07 / A12
Tank / cylinder evaporator sensor faulty
LED blinks, machine keeps running
A09
Safety magnet switch: front lid open
Close the lid
A11
High pressure switch tripped
Stops after repeated trips
A22
Production ran over 15 minutes without reaching HOT
Alarm shown
A24
Portion count reached the “last cones” setting
Machine goes to storage
A30
Tank above 15°C while stopped
Forces a pasteurisation cycle
LOW
Mix running out
Add mix
Stb
Standby, or product not ready to serve
Wait
PHS
Stopped by the phase controller
Check the supply

Why is my ice cream machine not freezing?

These are the causes in our job records on soft serve and gelato machines, roughly in order:
  • A blocked condenser. Dust on the condenser makes the refrigeration overheat; the compressor trips and the product stays soft. The Carpigiani guide also says that a compressor that starts and stops within seconds points to poor air circulation (or no water on water-cooled machines).
  • Low refrigerant. On one Carpigiani whose ice cream came out milky after the first portion, the refrigeration circuit needed regassing with R404A by our F-Gas engineer.
  • Drive faults. A failed gearbox (reductor) on the main cylinder, a burnt beater motor, a worn belt or a seized bearing. On one 191 SP the reductor had failed and the machine would not produce ice cream at all.
  • Electrical faults. Blown transformer fuses or thermofuses, failed relays, and control boards reporting a voltage error.

What you can check yourself

  • Keep the vents clear and clean dust from the condenser grille.
  • Close the front lid properly (A09) and tighten its knobs evenly.
  • Keep the mix topped up (LOW) and do not ignore the WAS reminder.
  • If the machine stops on an A01 to A05 alarm, or keeps tripping the pressure switch, call an engineer rather than resetting it again and again.

Ice cream machine service in London

Every repair starts with checking and cleaning, including the condenser. See also ice machine fault lights, commercial refrigeration repair and restaurant equipment maintenance.

Book an ice cream machine repair in London

LE Company’s call-out is from £175 + VAT and includes the first 30 minutes on site. The cost of the repair is agreed with you before any work starts. 12-month guarantee on parts — we fit only original manufacturer parts. Our engineers are F-Gas registered. Call +44 203 603 7172, Monday to Saturday, 8am to 8pm.

Book an engineer

Leave your details and what is wrong. The bookings team will email you the call-out cost and the times an engineer can come. Call-out from £175 + VAT, including the first 30 minutes on site.