Wolf oven error codes: what they mean and what to do
Most Wolf oven and range error codes point to one of four things: a thermal cut-out that has opened because something got too hot (3311, 3312), a cooling fan that has stalled (4910, 5521), lost communication between the control boards (6020, 6120) or, on older dual fuel ranges, a door lock that did not move in time during self-clean (01). This guide from LE Company, Wolf repair engineers in London, gives the meaning of each code as Wolf itself publishes it, what you can safely try, and what our engineers actually find inside Wolf ovens and ranges. For repairs, see our Wolf oven repair in London page.

Wolf oven error codes list
The meanings below come from two Wolf sources only: Wolf’s own owner help pages (subzero-wolf.com/assistance) and Wolf’s E Series General Information service manual (part no. 829345 REV A), which lists the wall oven codes. The same number can mean different things on different Wolf families, so check whether you have an E Series or M Series wall oven, a current dual fuel or induction range, or an older (legacy) dual fuel range.
Code | What Wolf says it means | Models |
3311 | TCO (thermal cut-out) open, upper or single oven | E Series ovens |
3312 | TCO open, lower oven | E Series wall ovens (service manual) |
3221 / 3222 | RTD (oven temperature sensor) open, upper or single / lower oven | E Series wall ovens |
3921 | Broil bank wiring fault, upper or single oven | E Series wall ovens (service manual) |
4910 | Upper cooling fan stall detected | E Series ovens; also shown on M Series wall ovens |
5521 | Primary stalled cooling fan: fan speed below the minimum | Dual fuel and induction ranges |
6020 | MCB (main control board) RS485 network fault | E Series SO3050 and DO3050 ovens |
6120 | MCB CAN network fault, “Call Service” | E Series wall ovens |
01 (ERR 01) | Door lock or unlock switches not sensed within 60 seconds while the door lock motor runs | Legacy dual fuel ranges |
PF | Power failure, or oven too hot for the cooking mode selected | Legacy dual fuel ranges |
COMM ERR | Communication with the oven controller lost | Legacy dual fuel ranges |
Wolf oven error code 3311 and 3312
Wolf’s help page for the E Series oven lists 3311 as “Upper Oven TCO is open” or “Single Oven TCO is open”, and the E Series service manual lists 3312 as the same fault on the lower oven. TCO stands for thermal cut-out: Wolf explains that it opens when it senses excessive heat, which stops the heating and protects the electronic controls. Wolf names four causes: a faulty TCO, a cooling fan problem, an airflow problem, or long use at a high temperature setting.
Wolf’s advice is to switch the home circuit breaker for the oven off for 30 seconds, switch it back on and test the oven again. If the code returns, book an engineer. We have seen 3311 on a Wolf dual fuel range in London: the oven was working again when our engineer arrived, the temperature test passed and no relays were stuck, but the plate of the smoke catalyst had come out. He advised a new thermal cut-out, a new cooling fan and a new smoke catalyst. On other Wolf ovens we have found the high-limit switch tripped next to a noisy cooling fan, and a tripped high-limit switch and fuse with burnt oil on the transformer board.
Wolf oven error code 4910 and 5521
Both are cooling fan codes. Wolf’s E Series page calls 4910 “Upper Cooling Fan HES Stall Detected”; for M Series wall ovens Wolf says only that service is required. Wolf lists 5521 on dual fuel and induction ranges as “Primary Stalled Cooling Fan”: the cooling fan speed is below the minimum threshold. For both codes Wolf gives no owner troubleshooting and says an engineer is needed.
The cooling fan keeps the electronics cool, so take these codes seriously. On one Wolf range our engineer found the control area at 60°C on arrival: the cooling fan motors had failed, and the heat had already damaged the control head, so all three fans and the control head were replaced. On another, a damaged door seal let the cooling fan draw oil into the electronics, and the power, standby and relay boards were affected. Dust around the cooling motor and a fan that rubs or starts late are things we find on a routine service, before any code appears.
Wolf oven error code 6020 and 6120
These are network codes between the control boards. Wolf lists 6020 on E Series SO3050 and DO3050 ovens as “MCB RS485 Network Fault”, and 6120 on E Series wall ovens as “MCB CAN network fault” with the message “Call Service”. Wolf’s advice for both: switch the breaker off for 30 seconds, switch it on and retest; if the code comes back, book an engineer.
When a Wolf oven loses communication, the cause is not always the board itself. On Wolf ovens and ranges we have traced it to a lost connection between the control panel and the relay module, to a faulty cable between two control modules, and to oil or water that had dripped onto connections and burnt them. The engineer tests the cables and connectors before any board is ordered.
Wolf range error code 01
On legacy Wolf dual fuel ranges, ERR 01 means the door lock or unlock switches were not sensed within 60 seconds while the door lock motor was running. Wolf lists it as a code that can appear during self-clean. Its advice is the same breaker reset; if that does not clear it, service is needed. In our job records the door lock is a real wear point: we have found a stuck door lock on the right-hand oven of a Wolf range, and replaced a main door lock together with the mode switch on another.
PF on a legacy dual fuel range is different: Wolf says it means the unit had a power failure or the oven is too hot for the mode selected. Turn the oven selector to a cooking mode and back to OFF, open the door to let the oven cool, then try the breaker reset.
RTD and wiring codes: 3221, 3222 and 3921
Wolf’s E Series service manual lists 3221 and 3222 as “RTD Open” (the oven temperature sensor circuit, upper or single and lower oven) and 3921 as “Broil Bank Wiring Fault” on the upper or single oven. For 3222 Wolf’s help page gives no owner troubleshooting. The manual’s checks for these codes run from the sensor or element wiring to the relay board. That matches what we see: on one Wolf range a slow top (broil) element in the left oven turned out to be a failed relay in that element’s circuit, not the element itself.
How to reset a Wolf oven error code
Wolf’s standard reset for its ovens and ranges is to switch the home circuit breaker for the appliance off for 30 seconds, switch it back on and test the oven again. If the code comes back, stop resetting it: the stored code is what the engineer reads first. If you use the Sub-Zero Group Owner’s App, Wolf notes that a code can stay on screen for up to 24 hours after the fault is fixed.
- Do reset once with the breaker, let a hot oven cool with the door open, and check nothing blocks the vents or the cooling air.
- Do take a photo of the code and the rating plate before you call.
- Do not open panels, test wiring or replace boards yourself: Wolf ovens run on mains voltage, and the range has a gas supply.
What our engineers find on Wolf ovens and ranges
From our job records, LE Company has had more than 400 Wolf requests since 2022, close to 400 of them for Wolf ovens, ranges and cooktops. Of about 160 written Wolf job notes from our engineers, close to 40 involve the ignition, more than 60 a control, relay or ignition board, and more than 40 include cleaning. Most faults do not show a code at all. What we find most often:
- Ignition. Igniters that are oily, cracked or slow, worn ignition leads, and failed re-igniter (spark) modules where one channel stops working. A burner that clicks but lights late is usually this. See our case of a Wolf oven not serviced for 4 years, where an ignition complaint turned out to be dirt.
- Control and relay boards. Boards damaged by heat, by oil that drips onto connections, or by a failed transformer. A test board often proves the fault on the first visit.
- Fuses and heating elements. On one Wolf dual fuel range the fuse tripped as soon as the ovens started heating: every element tested fine cold but showed a fault to earth when hot. Strong cleaning chemicals in the oven were a suspected cause. Read our Wolf oven fuse and burners job.
- Burners. Rusted or blocked burners, over-oiled burners and blocked injectors, and burners with metal wire from a scouring sponge caught around the igniter. On one range the cooker had been installed on the LPG setting on a natural gas supply; our Gas Safe engineer converted it.
- Cooling fans and convection fans. Noisy or slow fan motors, and a fan motor that vibrated because the wrong cleaning chemical had coated its impeller.
- Doors. Worn door seals, hinges and door locks. A damaged seal lets heat and grease reach the electronics.
For the owner-level checks, such as cleaning burner ports and what a blank display means, see common Wolf stove faults. For how we rebuilt an old range from original parts, read how we gave a second life to a Wolf oven.
Wolf range gas safety
If you smell gas, do not reset or switch anything: turn the gas off at the meter, open the windows and call the National Gas Emergency number, 0800 111 999. Gas valves, injectors, burners and gas conversions on a Wolf range are work for a Gas Safe registered engineer only. We have found gas leaks at valves on Wolf ranges, and in each case the appliance was made safe or disconnected before anything else was done. Our engineers are Gas Safe and F-Gas registered; see our Gas Safe registered engineers in London.
Every repair starts with checking and cleaning
Every repair we do starts with checking and cleaning the appliance, because most faults begin with dust, scale, grease or a blockage. On a Wolf that means grease on the igniters, dust on the cooling fan, oil on the connections and blocked burner ports. Use self-clean sparingly and avoid harsh chemicals and metal scourers; our Wolf oven usage guide explains why.
Book a Wolf oven repair in London
LE Company’s call-out is from £175 + VAT and includes the first 30 minutes on site, when the engineer finds the cause of the fault. The cost of the repair is agreed with you before any work starts. 12-month guarantee on parts — we fit only original manufacturer parts. The visit with the assessment is paid first. We work Monday to Saturday, 8am to 8pm; Sunday visits are for service-contract customers. Call +44 203 603 7172, or see our Wolf oven repair page, our oven repairs in London and our full range of appliance repair in London. If you also have a Sub-Zero, see our guide to Sub-Zero error codes, and read our frequently asked questions.