Meiko dishwasher error codes: what they mean and what to do


Meiko error codes are grouped by number: 1xx codes are about the wash tank and leaks (111 is water where it should not be), 2xx codes are about filling and the boiler (201 and 202 mean the machine did not fill in time), and 3xx codes are about pumping and heating (302 means the water is not draining, 304 means the tank is not heating). LE Company engineers repair Meiko and other commercial dishwashers in London, and behind a Meiko 111 in a Soho restaurant we found a failed waste water pump, which we replaced. The meanings below are taken from Meiko’s own operating instructions; the same number can mean something different on a newer M-iClean, so check your model.
Commercial dishwasher repair in a London restaurant kitchen

Meiko error 111

On Meiko FV and DV machines, error 111 means floor pan leakage: water has reached the base of the machine and set off the leak water switch. Meiko’s DV 270.2 operating instructions list the causes as a leak inside the machine (pump sump, motor and so on) or a defective leak water switch, and the remedy as repairing the leak and removing the water. Switching the machine off and on will not clear 111 while there is water in the floor pan.
In 2022 a restaurant in Soho called us about a Meiko dishwasher flashing 111. Our engineer found the waste water side faulty, replaced the waste pump and tested the machine. On the newer M-iClean range, 111 has a different meaning: water loss in the wash tank, and Meiko advises calling a service technician if it comes back.

Meiko error 201 and 202

Error 201 means the water level was not reached during the first filling, and 202 means the level was not reached early enough during filling. Both point to the water supply: check that the tap is fully open, that the Aquastop hose is not kinked and that the inlet filter is clean. If they are, the Aquastop or the boiler level switch may be defective.

Meiko error 204

Error 204 means that after the end of the post-rinse time the level switch still detected no change, so the booster pump did not move the rinse water. Meiko lists a defective booster pump, a loose booster pump plug, a defective start capacitor, a defective boiler level switch or a missing signal between the circuit boards. This one needs an engineer.

Meiko error 302 and 301

Error 302 means that when pumping out during the rinse programme the level did not fall below level 1: the machine is not draining. Clean the strainers and check that the drain hose and the floor gully are clear. If they are, the drain pump is soiled or defective, its rotor is loose or its start capacitor has failed. Error 303 is the same fault later in the drain. Error 301 means the number of circulation pumping cycles was exceeded, usually because the booster pump yield is too low, the rinse jets or the air trap are soiled, or there is condensate in the level pipe.

Meiko error 304

Error 304 means the tank temperature did not rise as expected. Meiko lists a defective tank heater or thermal fuse, a defective or badly fitted temperature sensor, or a faulty contactor. Error 205 is the same fault in the boiler (the rinse water heater). A machine that does not reach temperature does not disinfect, so do not keep washing with it.

Meiko error codes list

From Meiko’s DV 270.2 operating instructions (document 9625762). FV undercounter machines use the same numbers for the common codes.
Code
Meaning
Usual cause
001
EEPROM fault
EEPROM missing, wrongly plugged in, empty or with the wrong parameters
111
Floor pan leakage
Leak inside the machine, or a defective leak water switch
112
Dosage leakage
Leaking or defective dosing pump, damaged or kinked hose
201
Level not reached during first filling
Tap closed, Aquastop hose kinked, inlet filter soiled, Aquastop or boiler switch defective
202
Level not reached early enough during filling
As 201
203
No level change during emptying of the boiler
Booster pump defective or its plug loose
204
No level change after the post-rinse time
Booster pump, start capacitor, boiler level switch, circuit board signal
205
Boiler temperature increase not reached
Boiler heater or thermal fuse, temperature sensor, contactor
210, 211
Temperature sensor short circuit or interruption
Sensor cable and plug contacts, sensor defective or wrongly fitted
212
Boiler temperature too high
Contactor sticking, wrong or defective sensor
301
Circulation pumping cycles exceeded
Booster pump yield too low, rinse jets or air trap soiled, condensate in level pipe
302
Level does not fall below level 1 when pumping out
Drain pump soiled or defective, rotor loose, start capacitor, Aquastop not closing
303
Level does not fall below level 3 in time
As 302
304
Tank temperature increase not reached
Tank heater or thermal fuse, temperature sensor, contactor
305
Not enough water in the boiler for rinsing
Ventilation valve soiled, level switch defective, plug loose
306, 307
Tank level reading disrupted, tank level sensor defective
Air trap or hose of the level sensor, sensor or plug
308, 309
Hood drive fault (hood machines)
Hood, spindle or motor jammed, limit switch, scale

Meiko info 120 and info 121

On FV 40.2, DV 120.2 and FV 130.2 machines, InFO 120 means the tank is not heating or fresh water is not coming in: check that the water hose is connected, not kinked and that the supply is on. InFO 121 means the door is not closed or the door switch is defective. A door switch set is one of the parts we have replaced on Meiko machines, on a job in Covent Garden.

Meiko M-iClean error codes

The M-iClean range uses its own list, from Meiko’s M-iClean U manual (document 9209401). The ones we are asked about most:
  • 101: drainage level not reached; clean the drainage sieve.
  • 111: water loss in the wash tank.
  • 114: fine or coarse sieve missing.
  • 117, 118: top or bottom wash arm blocked or missing.
  • 200: boiler level not reached in time; open the water supply and clean the pre-filter.
  • 205: final rinse cycles insufficient; load the washware correctly.
  • 301: rinse aid empty. 311: detergent empty or suction lance blocked.
  • 407: change the demineralisation cartridge.
  • 502, 504: wash or final rinse temperature not reached while energy optimisation is active.
  • 601, 611: power supply fault or overheating of the frequency converter.

Meiko error 702 and 901

702 and 901 are not in the operating instruction tables; they are read from the machine’s service log, so they need an engineer. In 2024 a Meiko DV 120.2 in Mayfair showed 702 and was not heating the water. Our engineer found water on the main motor inverter, which was causing the error, and a blockage inside the rinse booster, which needed descaling.

What you can check yourself

  • Water tap fully open, inlet hose not kinked, inlet filter clean (201, 202, InFO 120).
  • Strainers, sieves and wash arms clean and fitted (302, 114, 117, 118). Clean them at the end of every service.
  • Drain hose and floor gully clear (302, 303). See also why a dishwasher is not draining.
  • Door closed properly (InFO 121), detergent and rinse aid topped up.
  • For 111, 204, 205, 304 and any code that comes back, call an engineer rather than resetting it again and again.

Meiko dishwasher repair in London

Every repair starts with checking and cleaning: strainers, wash arms, the drain and, in hard-water London, scale in the boiler and the pumps. For other makes, see Winterhalter error codes and Hobart dishwasher error codes. Planned servicing prevents many of these faults: see commercial catering equipment maintenance.

Book a Meiko dishwasher repair

LE Company’s call-out is from £175 + VAT and includes the first 30 minutes on site, when the engineer reads the codes and finds the cause. The cost of the repair is agreed with you before any work starts. 12-month guarantee on parts — we fit only original manufacturer parts. See our commercial dishwasher repair page or call +44 203 603 7172, Monday to Saturday, 8am to 8pm.

Book an engineer

Leave your details and what is wrong. The bookings team will email you the call-out cost and the times an engineer can come. Call-out from £175 + VAT, including the first 30 minutes on site.